my 65 re-paint!!
Moderator: Moderators
Re: my 65 re-paint!!
"The Mustang is full of Awesome"
Re: my 65 re-paint!!
Thanks everyone that cleared things up.
Nassi while I was looking at the air punch on ebay I also found an air nibbler this will make things a bit easier to fix my fender.
Cheers
Nassi while I was looking at the air punch on ebay I also found an air nibbler this will make things a bit easier to fix my fender.
Cheers
Hanging around... and around
Re: my 65 re-paint!!
OK, sorry about that. It probably will help somewhere but I tend to use a cutting disc or snips so I cant really help there mate.mjb0015 wrote:Thanks everyone that cleared things up.
Nassi while I was looking at the air punch on ebay I also found an air nibbler this will make things a bit easier to fix my fender.
Cheers
Anyway, all tools are usefull at some point so why not?
Re: my 65 re-paint!!
Took a few pictures under the dash of the cowl and it doesn't look to bad!
Started to strip paint off the roof, seems there are a few coats and it will take a bit of paint stripper to get it clean, the roof channels are reasonablly clean with a little surface rust.
Mark
Started to strip paint off the roof, seems there are a few coats and it will take a bit of paint stripper to get it clean, the roof channels are reasonablly clean with a little surface rust.
Mark
Hanging around... and around
Re: my 65 re-paint!!
You need to put a camera in the plenum, I suspect the blanking plate is to stop leaks. Pretty lucky not much paint on it.
-
- Mustang King
- Posts: 4716
- Joined: Wed Jul 28, 2010 6:15 am
Re: my 65 re-paint!!
Im with Shaun, or even pull the blanks off to see if it covers rust and get your hands up there for a feel around.Shaunp wrote:You need to put a camera in the plenum, I suspect the blanking plate is to stop leaks. Pretty lucky not much paint on it.
Converting Rust to Something Drivable
66 Fastback Fairstang Project http://www.mustangtech.com.au/Forums/vi ... art=0.html
67 convertibuild project http://www.mustangtech.com.au/Forums/vi ... art=0.html
Thought Collecting Couch http://www.mustangtech.com.au/Forums/vi ... =1739.html
Caddy Wacked http://www.mustangtech.com.au/Forums/vi ... art=0.html
66 Fastback Fairstang Project http://www.mustangtech.com.au/Forums/vi ... art=0.html
67 convertibuild project http://www.mustangtech.com.au/Forums/vi ... art=0.html
Thought Collecting Couch http://www.mustangtech.com.au/Forums/vi ... =1739.html
Caddy Wacked http://www.mustangtech.com.au/Forums/vi ... art=0.html
Re: my 65 re-paint!!
Ok will pull the blanks tomorrow and have a look, thanks.
Mark
Mark
Hanging around... and around
Re: my 65 re-paint!!
Put a camera up there & take pics. That is what Shaunp was talking about.mjb0015 wrote:Ok will pull the blanks tomorrow and have a look, thanks.
Mark
Kerry
To our wives and sweethearts. May they never meet
To our wives and sweethearts. May they never meet
Re: my 65 re-paint!!
Well most of the paint has been removed, damage is rear tail light panel stuffed, will get Jeremy from Image classics to replace that as its a bit out of my skill set, the right quarter panel looks not bad some small dents will fix, left quarter panel has some damage to it has been bogged up, looks like it has 10kgs of bog, unbelievable, might have to cut out a section and weld in a new piece, have to remove bog and see what I have got the rest of panel OK, boot lid best panel, roof OK had small ripple so filled with small amount of body filler, looks big but spread out to keep feathered with surround, roof channels have some areas of rust, Jeremy will be doing these two sections also.
Bonnet almost stripped, looks clean, but there is a small section where the panel bends really easily, what could be causing that? is the bonnet skin welded to the struts? Will be doing door tomorrow, will apply etch primer then look at fixing the trouble areas, lets hope not much else.
Both fenders not bad, small dents that have shit load of spray putty applied,will remove that and fix. I recon the front end had a prang the fenders don't match.
Anyone have any advise or suggestions, I'm open to anything!!!!!
Bonnet almost stripped, looks clean, but there is a small section where the panel bends really easily, what could be causing that? is the bonnet skin welded to the struts? Will be doing door tomorrow, will apply etch primer then look at fixing the trouble areas, lets hope not much else.
Both fenders not bad, small dents that have shit load of spray putty applied,will remove that and fix. I recon the front end had a prang the fenders don't match.
Anyone have any advise or suggestions, I'm open to anything!!!!!
Hanging around... and around
Re: my 65 re-paint!!
Looks like a good shell to me mate. What etch are you using.
Re: my 65 re-paint!!
I am get the protec brand its $50 buck for a litre
Hanging around... and around
Re: my 65 re-paint!!
Are you going to repair the left quarter yourself? If you can do that you will have no trouble with a tail light panel.
"The Mustang is full of Awesome"
Re: my 65 re-paint!!
been slow going lately, redone sump, removed and restoring starter and power steering recon will be re-installed soon.
Body work ongoing, will be taking to Image classics soon for panel replacements/repairs.
(Just wire brushed the old crappy paint off, will recoat in original black)
Body work ongoing, will be taking to Image classics soon for panel replacements/repairs.
(Just wire brushed the old crappy paint off, will recoat in original black)
Hanging around... and around